The right way to Set Up Optical Move & Rangefinder Sensors in iNav – Place/Altitude Maintain for FPV Drones


Flying an FPV drone in Place Maintain and Altitude Maintain modes might be considerably improved with the addition of Optical Move and Sonar (rangefinder) sensors. These sensors assist preserve a secure hover by offering exact knowledge concerning the drone’s place and altitude. On this tutorial, I’ll information you thru establishing these sensors in iNav.

Among the hyperlinks on this web page are affiliate hyperlinks. I obtain a fee (at no additional price to you) in case you make a purchase order after clicking on considered one of these affiliate hyperlinks. This helps assist the free content material for the neighborhood on this web site. Please learn our Affiliate Hyperlink Coverage for extra info.

This information is predicated on the directions offered by the producer of the optical circulate sensor I bought. These steps may not work for different forms of optical circulate/sonar sensors.

Why Add a Rangefinder and Optical Move Sensor?

Including a rangefinder and optical circulate sensor enhances your quadcopter’s stability and precision. The optical circulate sensor works just like the sensor in a pc mouse, capturing pictures of the bottom to find out motion. The rangefinder (sonar) gives extra correct altitude measurements in comparison with a barometer, which is particularly helpful throughout touchdown, although the utmost efficient altitude is commonly lower than a number of meters.

Required Elements

You will have two issues:

  • Optical Move and Rangefinder Sensor
  • A drone with an iNav-compatible flight controller and a spare UART

Microair Mtf 01 Ranger Finder Optical Flow Sensor Module

I’m utilizing the MicroAir MTF-01, a rangefinder sensor with built-in Optical Move functionality. It’s a terrific module as a result of the connection and setup are very easy, and it helps iNav. You may get the MTF-01 right here:

I like to recommend getting the bundle that features the USB to TTL programmer (FTDI adapter), as you may want it to alter settings, or you should buy a generic one if that’s cheaper, additionally works effective: https://oscarliang.com/fpv-tools/#FTDI-Adapter

MTF-01 Specs:

  • Helps Ardupilot, PX4, and iNav
  • PMW3901 optical circulate sensor
  • Excessive-performance TOF sensor
  • Output mode: UART
  • Output frequency: 100Hz
  • TOF Vary: 0.02-8m
  • Vary accuracy: 2%
  • Wavelength: 830-870nm
  • Resistance to ambient gentle: 70K Lux illumination
  • Distance FOV: 6°
  • Optical circulate FOV: 42°
  • Ambient gentle demand of optical circulate: >60Lux
  • Optical circulate working distance: >80mm
  • Energy consumption: 500mW
  • Working voltage: 4.0- 5.5V
  • Module weight: 4.5g
  • Dimensions: 29 * 16.5 * 15mm

For the drone, I’m utilizing the GEPRC Cinebot25. I’m not snug testing place maintain indoors with any drones with out prop guards, so a small cinewhoop is an ideal alternative. See my evaluate of this drone right here: https://oscarliang.com/geprc-cinebot25/

Nevertheless, the GEPRC flight controller doesn’t assist iNav (but), so I needed to swap it out with the Flywoo GN745 V3. Listed here are particulars about this FC and the way I changed it: https://oscarliang.com/flywoo-goku-gn745-aio-v3-fc/

New to iNav? Try my newbie tutorial on the way to arrange iNav on an FPV drone: https://oscarliang.com/setup-inav-fpv-drone/

Step 1: Configuring the Module

The MTF-01 module helps the next output protocols:

  • Microlink: a customized protocol which helps FMT
  • MSP: helps iNav
  • Mavlink_APM: Mavlink protocol for Ardupilot
  • Mavlink_PX4: Mavlink protocol for Pixhawk 4

My unit was set to Microlink by default, so I needed to change it to MSP protocol to work with iNav. You’ll be able to simply swap the output protocol of the MTF-01 utilizing the MicoAssistant software program, however you will want a USB to TTL programmer.

Obtain MicoAssistant software program: https://github.com/micoair/MTF-01_USER_MANUAL

Join the MTF-01 to your PC utilizing the USB to TTL module.

Microair Mtf 01 Ranger Finder Optical Flow Sensor Module Usb To Ttl Programmer

Open the MicoAssistant software program, choose the proper COM port within the higher proper nook, set the baud charge to 115200, and click on on the connection icon.

Microair Mtf 01 Ranger Finder Optical Flow Sensor Module Usb Microassistant Configure Connection

As soon as related, click on on the Setup Menu (gear icon), choose the protocol you wish to use (on this case, MSP), after which click on the WRITE button.

Microair Mtf 01 Ranger Finder Optical Flow Sensor Module Usb Microassistant Configure Output Protocols Msp

Step 2: Wiring the Sensors

Join the 4 wires from the MicroAir MTF-01 sensor to any spare UART in your flight controller. I related it to UART4 on my FC.

  • 5V to 5V
  • GND to GND
  • TX to RX
  • RX to TX

Notice: If the rangefinder and optical circulate sensor don’t get powered by way of the USB cable, you might need to plug in a battery to energy these sensors.

Microair Mtf 01 Ranger Finder Optical Flow Sensor Module Wiring Diagram Flight Controller Fc Uart Tx Rx

Flywoo Goku Gn745 45a Aio V3 Fc Flight Controller Replace Geprc Cinebot25 Taker G4 Wiring Gps Optical Flow

Mount the sensor on the underside of the quad, guaranteeing there’s nothing obstructing the view of the sensors. Use touchdown gears to make sure there’s adequate clearance between the bottom and the sensors throughout takeoff, ideally a few centimeters or extra.

Microair Mtf 01 Ranger Finder Optical Flow Sensor Module Install Geprc Cinebot25 Fpv Drone Cinewhoop Bottom

Step 3: Configuring iNav

Earlier than continuing, take away the propellers out of your quadcopter for security. Join the battery after which join the flight controller to your pc.

Ports

Open iNav Configurator, go to the Ports tab, and configure the UART you wired up as MSP. Save and reboot.

Inav Configurator Ports Setup Ranger Finder Optical Flow Sensor Msp

Configuration

Within the Configuration tab, discover the “Sensors & buses” part. For Rangefinder and Optical Move, set them to MSP. Save and reboot.

After rebooting, the “Move” and “Sonar” sensor icons on the highest of iNav Configurator ought to flip blue, indicating they’re working accurately. If these sensors don’t flip blue however crimson, test that the TX and RX wires are accurately related and that the battery is powering the sensors.

Inav Configurator Configuration Setup Ranger Finder Optical Flow Sensor

CLI Settings

Inav Configurator Cli Setup Ranger Finder Optical Flow Sensor Pid

Copy and paste the next strains within the CLI (these are configurations steered by the maker of MTF-01).

  • Lifeless Reckoning: by enabling iNav_allow_dead_reckoning within the CLI, it enhance efficiency throughout transient GPS outages.
  • Most Top Setting: by setting the inav_max_surface_altitude within the CLI, it defines the utmost peak at which the rangefinder is efficient, in cm.
set nav_mc_vel_z_p = 150 set nav_mc_vel_z_i = 250 set nav_mc_vel_z_d= 25 set nav_mc_pos_xy_p = 80 set nav_mc_vel_xy_p = 50 set nav_mc_vel_xy_i = 40 set nav_mc_vel_xy_d = 60 set debug_mode = FLOW_RAW set inav_allow_dead_reckoning = ON set nav_max_terrain_follow_alt = 200 set inav_max_surface_altitude = 200 save

Debug

Within the Sensors tab, gently tilt the quad aspect to aspect and entrance to again. The waveform of Debug 0 ought to look much like Debug 2, whereas Debug 1 ought to look much like Debug 3.

Debug 0/1 represents the accelerometer readings, whereas 2/3 are from the optical circulate sensor. This check verifies the orientation of the optical circulate sensor. The amplitude may not be the identical, but when they transfer in the other way, you may want to alter the configuration in MicroAssistant (or set align_opflow=cw180 in CLI).

Inav Configurator Debug Setup Ranger Finder Optical Flow Sensor

Calibration

Maintain the drone round 50-60 cm above the bottom and carry out the optical circulate sensor calibration in iNav Configurator. This entails gently tilting the quad aspect to aspect and entrance to again barely and gently for about 30 seconds with none horizontal actions. Hit save and reboot when finished.

MTF-01 recommends a scale worth between 4 to six. If you happen to get a price outdoors this vary, repeat the calibration at a greater peak with extra regular palms.

Inav Configurator Calibration Setup Ranger Finder Optical Flow Sensor Scale

Modes

Assign a swap that may allow ANGLE, NAV POSHOLD (place maintain), NAV ALTHOLD (altitude maintain), HEADING HOLD, and SURFACE on the identical time.

Inav Configurator Modes Setup Ranger Finder Optical Flow Sensor Altitude Position Hold

Step 4: Testing the Setup

  1. Arm the drone and raise it right into a hover. If it doesn’t arm because of the lack of GPS lock, bypass this by pushing the throttle/yaw follow the underside proper whereas arming.
  2. Change to Place Maintain mode and observe the steadiness.
  3. Change to Altitude Maintain mode and test the altitude stability.

Troubleshooting and Professional Suggestions

    • Sensor Initialization Failure: Make sure the wiring is right and the sensors are powered.
    • Inaccurate Place Maintain: Modify the Optical Move scaler worth.
    • Altitude Drifting: Recheck the Rangefinder configuration and calibration.
    • Initialization Clearance: Guarantee there may be at the least a few centimeters of clearance between the sensor and the bottom when powering up the quadcopter to keep away from incorrect readings.

Conclusion

Including the MTF-01 rangefinder and optical circulate sensor to your iNav FPV drone is a simple course of that considerably enhances the steadiness and precision of your drone in Place Maintain and Altitude Maintain modes, in addition to touchdown accuracy. With these sensors, your quadcopter will carry out extra like a DJI digital camera drone, holding its place and altitude with better precision. Comfortable flying!

Recent Articles

Related Stories

Leave A Reply

Please enter your comment!
Please enter your name here

Stay on op - Ge the daily news in your inbox